KMZ (Karacharovsky Mechanical Plant) lifts: shaft dimensions
Russia · Moscow. 3 series, 18 sizes. Rated load from 320 to 400 kg, shaft width 1240–1700 mm, depth 1450–1700 mm.
About the manufacturer
PJSC Karacharovsky Mechanical Plant, Moscow, 2 Ryazansky Prospekt. Founded in 1950, more than 290,000 lifts produced, a 14.2 ha site, 34,500 m² of workshops, 27,500 m² of warehouses, capacity of 10,000 lifts a year, more than 2,100 specialists, over 100 types of lift equipment, warranty up to 5 years. In the first half of 2026 it increased installations by 36% to 1,800 units — the only major Russian plant growing in a falling market. Model range: Moskvich, Vozdukh, Oniks, Altius, Sirius+, Sirius, Panoramus, Pegas, FKR, Atlant, Alkor, Medius. Declared range: 250–5,000 kg, speed 1–4 m/s, door 600–2,400 mm, single-entrance or through car, with and without machine room, versions for people with reduced mobility, and a firefighters' version. According to the plant, it was the first in Russia to certify its products to GOST 33984.1-2016, harmonised with EN 81-20.
SOURCE OF DIMENSIONS. The data come from the “Design brief for the building part” LP-K0411-650(700).00.00.000B SZ, developed by the plant on 08.12.2022. The plant states: dimensions without tolerances are for reference; the drawing is to be read only together with the “General provisions for designing the building part of KMZ lifts” on kmzlift.ru; the plant may make changes without prior notice.
IMPORTANT ABOUT THE PIT. The standard pit depth is 1,100 mm at 1.0 m/s and 1,250 mm at 1.6 m/s. The plant explicitly allows a reduction to 800 mm (at 1.0 m/s) and to 900 mm (at 1.6 m/s) with special safety devices — this is shown as a separate series and falls into the “for existing buildings” category.
MORE FROM THIS SHEET. Structural opening width: 800 mm with a 650 door and 850 mm with a 700 door, wall opening height 2,050 (+90) mm; clear door opening 650(700)×2000. Side counterweight: shaft 1,600–1,700 with a 650 door and 1,650–1,800 with a 700 door, depth 1,450–1,700 mm, distance to the counterweight axis Lside = Wshaft/2−80 with a 650 door and Wshaft/2−55 with a 700 door. Rear counterweight: shaft 1,420–1,700 with a 650 door and 1,520–1,800 with a 700 door, depth 1,600–1,850 mm. A mirrored right-hand counterweight is possible. Outer car size 1022×1165 with a clear 950×1100, car height 2,100 mm.
OTHER VERSIONS. Sirius with a rear counterweight has been added from its …000 SZ sheet. The Pegas LP-P series was added on 18.09.2026 from eight sheets published by the plant on BIMLIB (nine cards, two share one sheet): LP-P0320-650TL(TP), LP-P0401-800, LP-P0411-650(700) and …B, LP-P0411-700TP(TL) and …B, LP-P0411-800TP(TL) and LP-P0411-800TL(TP)…B. Pegas needs a 1,150 mm pit at 0.71–1.0 m/s and 1,250 at 1.6, top floor height 3,400 and 3,600 — unlike Sirius (1,100 and 3,450). The plant allows a reduced pit of 800 mm (1.0 m/s) and 900 mm (1.6 m/s) with special safety devices here too. Structural wall opening per the plans: 770 mm with a 650 telescopic door, 800/850 with 650/700 centre-opening, 850 with a 700 telescopic, 920 with an 800 telescopic, 950 with an 800 centre-opening door. For shafts narrower than 1,400 mm (700 telescopic, rear counterweight) and 1,500 mm (800 telescopic) the plant requires a niche for the overspeed governor. A separate warning: the short model descriptions on BIMLIB sometimes differ from the forms themselves — for example, for this version the description gives a shaft of 1600(1900)×1450(1750), while the form says 1600–1700 with a 650 door and 1650–1800 with a 700 door. We treat the form, not the card, as the source of truth.
Questions about the brand — info@liftoteka.ru.
Series
Updated: 22 September 2026