Lift pit: depth and requirements
The pit is the part of the shaft below the lowest landing: it holds the buffers, the overspeed governor tension pulley and the safety space for a person under the car. In manufacturers' catalogues the depth ranges from 245 mm for home lifts to 7,200 mm for high-speed and freight lifts.
Pit depth depends not on rated load but on speed and buffer type. For a typical passenger lift at 1.0 m/s it is 900–1,350 mm, at 1.6–1.75 m/s 1,250–1,600 mm, for high-speed lifts from 2.5 m/s 1,700 mm and more. Values below 500 mm in the tables relate to home lifts and reduced-pit solutions: they fall under a different regulatory framework and must not be applied to an ordinary lift.
What GOST 33984.1-2023 requires
The standard does not set a minimum pit depth as a number. It defines what must fit into the pit when the car is at its lowest position, and the depth follows from that:
- Safety space for personnel (table 4) — at least one free refuge space of one of three types must remain on the pit floor: “upright” 0.40 × 0.50 m, 2.00 m high; “crouching” 0.50 × 0.60 m, 1.00 m high; “laying” 0.70 × 1.00 m, 0.50 m high. If more than one person works in the pit, one space is needed per person, all of the same type.
- 0.50 m — vertical distance between the pit floor and the lowest protruding parts of the car (cl. 5.2.5.8.2 a). Under the car apron and vertically sliding car door parts it may be reduced to 0.05 m, under protruding parts of the car frame, safety gear and guide shoes — within the limits shown in figures 6 and 7 of the standard.
- 0.30 m — free distance between the highest parts fixed in the pit (tension device, jack supports, pipes) and the underside of the car (cl. 5.2.5.8.2 b).
- If the safety space does not fit (cl. 5.2.5.8.3), a permanently installed mechanical device is mandatory that stops the empty car travelling at inspection speed and holds it stationary; opening the pit door and activating the device are monitored by electrical safety devices, and while the device is active the car can be moved only from the inspection station in the pit. A “shallow pit” without these devices does not comply.
The practical conclusion: a pit shallower than 500 mm physically cannot hold even the lowest “laying” safety space. Such a lift is either installed to GOST 34581-2019 (EN 81-21) — new lifts in existing buildings, with a mechanical car stopping device of safety integrity level SIL 3 — or it is a home lift or lifting platform to which GOST 33984.1 does not apply in this respect.
What to do when you cannot dig
204 sizes in the reference fit a pit of up to 1,030 mm. This is the solution for reconstruction, add-on shafts and sites where the foundation, a car park or groundwater lies below floor level. The shallowest value in the catalogues is 245 mm, but that is a home lift in an aluminium shaft, not a passenger lift to GOST 33984.1.
Lifts with a shallow pit Select for your shaft (RU)
Table: shallowest pits
| Pit | Series | Shaft clear b3×d2, mm | Brand | Rated load | Speed |
|---|---|---|---|---|---|
| 245 mm * | PAP-HYD-LPH | 1100 × 1730 | PAPPAS Elevators | 300 kg | 0.63 m/s |
| 245 mm * | PAP-HYD-LPH | 1330 × 1800 | PAPPAS Elevators | 300 kg | 0.63 m/s |
| 250 mm * | LV-HOMI | 1600 × 1650 | LINVOL | 400 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1350 × 1500 | XIZI Elevator | 250 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1550 × 1470 | XIZI Elevator | 250 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1450 × 1600 | XIZI Elevator | 320 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1750 × 1570 | XIZI Elevator | 320 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1500 × 1700 | XIZI Elevator | 400 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1750 × 1670 | XIZI Elevator | 400 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1530 × 1650 | XIZI Elevator | 400 kg | 0.4 m/s |
| 280 mm * | XZ-VILLA1 | 1820 × 1600 | XIZI Elevator | 400 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1760 × 1400 | Shanghai Mitsubishi | 320 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1520 × 1450 | Shanghai Mitsubishi | 320 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1610 × 1430 | Shanghai Mitsubishi | 320 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1760 × 1400 | Shanghai Mitsubishi | 400 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1700 × 1450 | Shanghai Mitsubishi | 400 kg | 0.4 m/s |
| 285 mm * | SM-LEON2V | 1710 × 1430 | Shanghai Mitsubishi | 400 kg | 0.4 m/s |
| 300 mm * | GRV20 | 1380 × 1450 | Sicher / SRH | 320 kg | 0.22 / 0.28 m/s |
| 300 mm * | GRV20 | 1480 × 1450 | Sicher / SRH | 400 kg | 0.22 / 0.28 m/s |
| 305 mm * | PAP-HYD-LPH | 1200 × 1980 | PAPPAS Elevators | 450 kg | 0.63 m/s |
| 305 mm * | PAP-HYD-LPH | 1430 × 2050 | PAPPAS Elevators | 450 kg | 0.63 m/s |
| 305 mm * | PAP-HYD-LPH | 1300 × 2135 | PAPPAS Elevators | 630 kg | 0.63 m/s |
| 305 mm * | PAP-HYD-LPH | 1535 × 2200 | PAPPAS Elevators | 630 kg | 0.63 m/s |
| 320 mm * | XZ-VILLA3 | 1450 × 1400 | XIZI Elevator | 250 kg | 0.4 m/s |
| 320 mm * | XZ-VILLA3 | 1550 × 1500 | XIZI Elevator | 320 kg | 0.4 m/s |
| 320 mm * | XZ-VILLA3 | 1550 × 1600 | XIZI Elevator | 400 kg | 0.4 m/s |
| 320 mm * | XZ-VILLA3 | 1625 × 1400 | XIZI Elevator | 250 kg | 0.4 m/s |
| 320 mm * | XZ-VILLA3 | 1725 × 1450 | XIZI Elevator | 320 kg | 0.4 m/s |
| 320 mm * | XZ-VILLA3 | 1725 × 1500 | XIZI Elevator | 400 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1600 × 1600 | Tenau | 250 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1650 × 1600 | Tenau | 320 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1800 × 1600 | Tenau | 400 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1450 × 1600 | Tenau | 250 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1550 × 1600 | Tenau | 320 kg | 0.4 m/s |
| 350 mm * | TN-VILLA-R | 1650 × 1600 | Tenau | 400 kg | 0.4 m/s |
| 400 mm * | PAP-MRL470 | 1500 × 1600 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRL470 | 1500 × 1830 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRL470 | 1600 × 1800 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | PAP-MRL470 | 1600 × 1980 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | PAP-MRL470 | 1600 × 2450 | PAPPAS Elevators | 1000 kg | 1 m/s |
| 400 mm * | PAP-MRL470 | 1600 × 2680 | PAPPAS Elevators | 1000 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1530 × 1600 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1530 × 1830 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1590 × 1600 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1590 × 1830 | PAPPAS Elevators | 450 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1630 × 1800 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1630 × 1980 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1690 × 1800 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | PAP-MRLL | 1690 × 1980 | PAPPAS Elevators | 630 kg | 1 m/s |
| 400 mm * | XZ-VILLA2 | 1400 × 1400 | XIZI Elevator | 250 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1550 × 1400 | XIZI Elevator | 320 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1750 × 1400 | XIZI Elevator | 320 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1600 × 1500 | XIZI Elevator | 400 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1750 × 1500 | XIZI Elevator | 400 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1570 × 1450 | XIZI Elevator | 400 kg | 0.4 m/s |
| 400 mm * | XZ-VILLA2 | 1800 × 1450 | XIZI Elevator | 400 kg | 0.4 m/s |
| 455 mm * | PAP-HYD | 1100 × 1675 | PAPPAS Elevators | 300 kg | 0.63 m/s |
| 455 mm * | PAP-HYD | 1275 × 1800 | PAPPAS Elevators | 300 kg | 0.63 m/s |
| 455 mm * | PAP-HYD | 1200 × 1925 | PAPPAS Elevators | 450 kg | 0.63 m/s |
| 455 mm * | PAP-HYD | 1375 × 2050 | PAPPAS Elevators | 450 kg | 0.63 m/s |
A pit shallower than the catalogue value is possible only with the manufacturer's consent and usually requires additional safety devices. This is confirmed by the layout sheet, not by a table.
Related
Updated: 22 September 2026